URL: www.nopallux.rs/proizvodi/proizvodi/sip/primera/pild-1010.html

Products > Switch Ranges > Primera > Programmable intelligent LED dimmer 10-100W/VA with potentiometer and push-push switch

Programmable intelligent LED dimmer 10-100W/VA with potentiometer and push-push switch

Primera Classic

Programmable intelligent LED dimmer 10-100W/VA with potentiometer and push-push switch
• For dimmable LED lamps 230V~ and low voltage dimmable LED lamps via electronic transformers, 1-10 LEDs
• 3 working modes to match most types of LEDs
• Adjustable minimum brightness
• For dimmable CFL lamps
• For incandescent and halogen bulbs 230V~ 50Hz
• For low-voltage halogen bulbs with toroidal or electronic transformers
• Microprocessor based overload protection, automatic turn-off
• More dimmer combinations is not allowed
• Screw contacts 1,5-2,5mm2
• For mounting in wall box ø60

ART.860411- Signal white
ART.860412- Warm white

pack. bag: 10



Primera Line

Programmable intelligent LED dimmer 10-100W/VA with potentiometer and push-push switch)
• For dimmable LED lamps 230V~ and low voltage dimmable LED lamps via electronic transformers, 1-10 LEDs
• 3 working modes to match most types of LEDs
• Adjustable minimum brightness
• For dimmable CFL lamps
• For incandescent and halogen bulbs 230V~ 50Hz
• For low-voltage halogen bulbs with toroidal or electronic transformers
• Microprocessor based overload protection, automatic turn-off
• More dimmer combinations is not allowed
• Screw contacts 1,5-2,5mm2
• For mounting in wall box ø60

ART.860421- Signal white
ART.860422- Warm white

pack. bag: 10




COMPATIBILITY AND LOADING ADVICE

Dimmer is not suitable for:

Dimmer is recommended for:

DIMMABLE LEDS

Always choose LEDs that are described as „dimmable” and for the best performance choose dimmable LEDs from established brands. We cannot guarantee that all LEDs labeled as „dimmable” can actually be dimmed satisfactorily. The dimming performance of dimmable LEDs may be improved by following the steps under the heading >“Optimizing The Performance of the Dimmer”.



TRANSFORMERS

Use only with quality dimmable transformers. To calculate load, add the VA ratings of the transformers (not the wattage of the bulbs). Choose transformers with a maximum rating close to their lamp load (e.g. Use a 50VA, 60VA or 70VA transformer to control a 50W low voltage bulb).
N.B. Certain transformers may not behave according to their power rating when used with a dimmer. An overload will result in the safety features switching the dimmer off. If so, change your transformer(s) or remove one (or some) transformer(s) from the circuit, or choose a higher rated dimmer.

IMPORTANT:

Read „Compatibility and Loading Advice“ section before installing this dimmer. Dimmer is leading-edge and designed to control dimmable LED lighting. To optimize the dimming performance with LED lighting see “Optimizing the Performance of Your Dimmer” below. For information on compatibility with other types of lighting please see „Compatibility and Loading Advice” section.
This product complies with European Safety Regulations (IEC 60669-2-1 i EN 60669-2-1) when used in lighting circuits containing MCBs (miniature circuit breakers). These can be rated at 6A, 10A or 16A (preferably 6A for lighting circuits).


OVERLOAD PROTECTION:

This dimmer switch is protected against overheating. If an overload occurs the dimmer will turn the lights down to indicate there is a problem. Then the dimmer will automatically turn off until the overload is removed and the dimmer is switched off and then is switched back on again. However, if the dimmer receives a total short-circuit it may be damaged beyond repair.


FITTING YOUR DIMMER:

Read these instructions carefully. Incorrect installation may damage the dimmer beyond repair. In case of any doubt or difficulty consult a qualified electrician.

OPTIMIZING THE PERFORMANCE OF YOUR DIMMER

When you first install the dimmer it will automatically default to MODE1. This mode is the best one for almost all types of LED lighting but if the lights are flashing in MODE1 you may be able to improve the dimming performance by changing the driving mode. (See „Changing the driving mode” below.) You can always reset to MODE1. Additionally, the minimum brightness setting of the dimmer can be adjusted to achieve the optimum dimming range for a particular load as follows.


Adjusting the minimum brightness

If your lights are flickering when they are dimmed to a low level you can increase the minimum brightness setting of the dimmer, which may prevent this from happening. If the lights are brighter than you would like when dimmer is set to minimum, you can try reducing the minimum brightness setting of the dimmer.

Changing the driving mode

Unless the lights are flashing it is likely that the best dimming performance that the lamps can deliver is achieved in MODE1. If the lights are flashing then you may be able to improve the performance of your lamps by manually changing the driving mode to MODE2, or in small number of cases, MODE3.

Resetting the dimmer

If you change your lights you can reset the dimmer to the factory default minimum brightness setting.



Wiring diagrams

One-point control


Two-point control


Three-point control




Copyright © Nopal Lux - All rights reserved
www.nopallux.rs